Janet, Mamod, IP Engineering Jane spares, and upgrades
MMS and original Mamod locomotive spare parts
I still
have a few parts but stocks are gradually diminishing and will not
be replaced
Gasket set for port face (2 per set)
Loco and wagon buffers (2 per set)
Red drag beam plate
Cast drag beam
Cab hand rails, brass (4 per set)
Cab back unpainted
Cab front only unpainted
Cab roof only unpainted
Cab roof latch spring
Cab spectacle rings, each
Left or right side tanks unpainted (each)
Pre-set safety valve at 14psi
Steam whistle assembly Back water level brass plate
Combustion chamber
Chassis frames (set of 2)
Solid fuel burner tray
Loco coupling rods (2) washers and circlips
Loco and wagon coupling hook
Loco and wagon coupling rings (2)
Ready built loco wheels and axle assembly
Chimney and smokebox assembly
Smokebox handle and screw
Standard loco chassis spacer and screws
Wagon wheels (2 axles) 45mm or 32mm gauge
NEW brass insert to enable original Mamod brass dome to be used on Janet boiler
£2
£8
£3
£8
£8
£10
£12
£4
£1
£1
£15
£6
£8
£5
£10
£12
£6
£6
£3
£2
£18
£14
£1
£1.50
£8
£5
I have a very limited number of pre-coloured Mamod parts as below. I am unlikely to be able to replace these once sold.
Cab back painted black, unlined
Cab back painted red, lined
Tank left or right painted green unlined
Tank right or left painted red, lined
Cab roof painted black
Cab roof painted green
£23
£12
£18
£18
£5
£5
Modifications and enhancements for MMS and standard original Mamod locomotives
The following fittings, mainly sourced locally or made by ourselves, will transform the performance of your locomotive. The piston assembly and forward reverse valve are high quality and very efficient products.
The video alongside, taken by Chris Bird and shown courtesy of him, shows his elderly Mamod fiited with our cylinders and reversing valve and a Summerlands Chuffer. He has also fitted radio control.
Our models and parts are exclusively made in England
‘O’ ringed piston and cylinder set (2)
Forward reverse valve assembly
Silver soldered copper 'Janet' boiler with sight glass, top–up valve, safety valve (40psi), regulator,and take off for pressure gauge
De Winton boiler with sight glass, top-up valve, safety valve, banjo fitting and pipe for steam take off and take-off for pressure gauge.
Globe valve with de-luxe cast handle
(regulator as on DW)
¾” pressure gauge
½” pressure gauge
Syphon (to connect pressure gauge)
please note that this is necessary to
connect
pressure gauge
NEW discs wheels with holes, inc
bearings
Spoked wheels no longer available
If buying wheels as replacements for Mamods or MSS locos I'd very much recommend buying a pair of my coupling rods too. - £5 pair.
Steam regulator (fits in the cab)
Adjustable safely valve for standard boiler (¼x26tpi)
(also available in 1/4 40tpi)
Water Top-up valve ¼ x 26tpi BSF
(also available in ¼ 40tpi)
Janet chassis frames (pair) (thicker than Mamods)
De Winton chassis frames (pair)
NEW Janet chassis, complete and tested
as photos to right
NEW De Winton chassis as
above
Displacement lubricator as Janet (no drain)
Displacement lubricator as janet with drain
Janet Gas burner with gas tank, pipe and jet
Janet Gas burner only
De Winton ceramic burner, gas tank and jet
Gas tank only
Gas tank ‘Ronson’ inlet valve
Gas jet No 3 or No 5 for burner
Gas pipe and jet
Brass hand rail kit (4)
Cast centre buffers, per pair
Multi height buffers, per pair
£85
£29.50
£145
£180
£25
£27.50
£32
£13
£39.50
£25
£10
£9
£15
£15
£190
£195
£19.50
£24
£77.50
£29.50
£95.00
£35
£6.50
£5
£12
£9
£5
£5
De Winton boiler. more photos on latest news page
New Disc wheels with holes
Complete Janet chassis
running
and tested on air
De
Winton chassis also available
Gas tank details - measurements
approximate
This
will be updated as soon as I have the new stocks
in.
If you are searching for something that is not listed, please call or email. I have lots of things that are not necessarily on here. For example, all parts for Janet and de Winton can be purchased subject to availability.